Owatrol Textrol Penetrating Oil Finish for Wood

Please Note swatches are given as a guide only and are based on use for light coloured softwoods. Actual colour will depend on the type and age of the wood surface treated. Always test a sample first before coating the entire surface.

Surface Preparation

New wood surfaces

New wood surfaces have a hard shiny surface known as mill glaze which prevents maximum penetration and bonding of any finish. To properly prepare the surface for application, and minimise splitting, swelling, cupping and checking caused by exposure to the sun and rain, first treat with Seasonite and allow the wood to weather for 6-12 months before applying Textrol.

Weathered wood surfaces

All surfaces must first be clean, dry and free of dirt, grease, grime and mildew. If any mildew is present, treat it with a solution of 1 part bleach to 3 parts water. Scrub the solution on to the surface and allow to stand for 10-15 minutes then rinse thoroughly. Clean weathered wood with Net-Trol to remove the loose wood fibres, dirt and other surface contaminants. If necessary sand the surface after cleaning (80 grit paper). After cleaning, allow the wood to dry for 2-3 days before finishing.

Previously oiled surfaces

Textrol may only be applied to bare wood surfaces or a weathered wood that was previously finished with Textrol. All other oils or sealers must be completely and thoroughly removed with a wood oil remover such as Owatrol’s Aquanett and then the surface must be cleaned and neutralised with Net-Trol before applying Textrol. If necessary sand the surface after cleaning and stripping (80 grit paper). After cleaning, allow the wood to dry for 2-3 days before finishing.

Previously coated surfaces

Textrol may only be applied to bare wood surfaces or a weathered wood surface that was previously finished with Textrol. All previous coating must be completely and thoroughly removed with a stripper such as Owatrol’s Dilunett and neutralised with Net-Trol before applying Textrol. If necessary sand the surface after cleaning and stripping (80 grit paper). After cleaning, allow the wood to dry for 2-3 days before finishing.

Application of Textrol penetrating wood oil

Application Tools

• Brush
• Roller
• Air-less sprayer .011 – .015 fluid tip/ 700-800 psi or less
• Garden sprayer

Apply the first coat of Textrol and allow it to penetrate into the wood (15-30 minutes). Apply a second application and allow it to penetrate for 15-30 minutes. If required repeat this procedure until the wood is saturated i.e. will accept no more oil. Do not allow Textrol to become touch dry or dry between coats. Once the timber is saturated, brush out or wipe up any excess product that has not penetrated to avoid shiny spots. NOTE: Textrol is not a surface coating, its place is in the wood not on the surface.

Maintenance

Decks & other horizontal surfaces

Most decks & horizontal surfaces will only require a maintenance application of Textrol every other year. A single application of Textrol every other year will be sufficient to refresh the natural beauty of the deck/horizontal surface and to maintain protection. A periodic clean between applications with Net-trol to remove dirt and contamination will renew the appearance of the wood.

Cladding & other vertical surfaces

Most cladding and vertical surfaces will only require touch up applications of Textrol. When areas treated with Textrol turn grey, clean with Net-trol and apply a single application of Textrol to replace material which has weathered out. Areas retaining good colour do not need a maintenance application. Badly weathered areas may require 2 applications of Textrol (apply the second application as soon as the first has penetrated the wood). Surfaces with harsh exposures to the sun and weather will weather wear more quickly than other areas. If this happens, clean effected areas with Net-Trol and apply Textrol as necessary, blending into areas which still have good colour.

Clean Up

Clean all tools and equipment with white spirit whilst still wet. If allowed to dry, remove with paint stripper.

NOTE: Any rags, steel wool etc. soaked in Textrol may spontaneously catch fire if improperly discarded. These must be saturated with water after use or placed in a sealed, water filled metal container, before disposing with household waste.

Things to Remember

• Before starting, test the colour choice on a small area. Allow to dry to determine final colour (remember that this colour will lighten over a couple of months to the final colour).
• Cover everything you do not wish to coat, including plants and shrubs.
• Apply between 5°C and 35°C.
• Do not apply if cold and/or wet weather is expected within 24-48 hours.
• Mix product thoroughly before and during application.
• Do not thin.
• Always work the entire length of a deck board or horizontal siding to a logical break, such as a window or door frame.
• Never stop the application in the middle of the wall.
• Vertical siding should be coated from top to bottom.
• Do not allow to dry between coats – apply Textrol ‘wet on wet’
• After spray application, always back-brush or back-roll to improve penetration and uniformity of coverage
• If using an airless sprayer it should be .011 – .015 fluid tip/ 700-800 psi or less